OLYMPIC HEAVY DUTY POWER RACK 9’(OHDPR9)Part # 7671001Rev. ARevision:12/10/031ASSEMBLY INSTRUCTIONS
10STEP 7:FIGURE 7• Securely tighten all loose frame connections made to this point.TIGHTEN!TIGHTEN!TIGHTEN!TIGHTEN!
11STEP 8:FIGURE 8• LOOSELY assemble one RIGHT & one LEFT ADJUSTMENT RACK (9 & 10) to the REAR UPRIGHTS (4) as shown, using eight3/8 X 3-3/4
12STEP 9:FIGURE 9• SECURELY assemble the ten WEIGHT HORNS (11) to the WEIGHT HORN UPRIGHTS (6) using twenty 1/2 X 4-1/4” BOLTS (26),twenty 1/2” INT
13STEP 10:FIGURE 10• Assemble two SWIVEL SPOTTERS (25) to the BOTTOM UPRIGHT SUPPORT (15) as shown using four 1/2 X 1-1/2” BOLTS (17), four1/2” F
14STEP 11:FIGURE 11• Insert the LEFT BAR SUPPORT (12) into the desired slots of the LEFT ADJUSTMENT RACK (10), and allow it to drop down to lock inpl
15STEP 12:FIGURE 12• Insert the BAR CATCHES (14) into the desired slots on the LEFT & RIGHT ADJUSTMENT RACKS (10 & 9), and allow it to drop d
Clean:• Upholstery with mild soap and water.• Guide rods with a cotton cloth.• Hand grips with mild soap and water.• Frame damage can be repaired with
PARTS LISTPART #LEA7586101LEA7586501LEA7656601LEA7656901LEA7585801LEA7586601LEA7586901LEA7588301LEA7584401LEA7584501LEA7587501LEA7587901LEA7587801LEA7
317 1/2 X 1-1/2” BOLT16 1/2 X 4-1/2” BOLT213/8” INT TOOTHLOCK WASHER201/2” INT TOOTHLOCK WASHER26 1/2 X 4-1/4” BOLT18 3/8 X 3-3/4” FLAT HEAD BO
STEP 1:FIGURE 14• LOOSELY assemble the REAR UPRIGHT (4) to the LEFT UPRIGHT BASE (1) using two 1/2 X 4-1/4” BOLTS (26), two 1/2” PLASITCDOME WASHERS
5STEP 2:FIGURE 2• LOOSELY assemble the BOTTOM UPRIGHT SUPPORT (15) to the REAR UPRIGHTS (4) using four 1/2 X 4-1/4” BOLTS (26), four1/2” PLASITC DOM
6STEP 3:FIGURE 3• LOOSELY assemble the FRONT UPRIGHT (3) to the LEFT UPRIGHT BASE (1) using two 1/2 X 4-1/4” BOLTS (26), two 1/2” PLASITCDOME WASHER
7STEP 4:FIGURE 4 7• LOOSELY assemble the REAR UPPER SUPPORT (7) and the CROSS SUPPORTS (5) to the REAR UPRIGHTS (4) using four 1/2 X 4-1/2” BOLTS (
8STEP 5:FIGURE 5• LOOSELY assemble the CHIN-UP SUPPORT (8) to the CROSS SUPPORTS (5) and the FRONT UPRIGHTS (3) using two 1/2 X 4-1/2”BOLTS (16), tw
9STEP 6:FIGURE 6• LOOSELY assemble the WEIGHT HORN UPRIGHTS (6) to the LEFT & RIGHT UPRIGHT BASE (1 & 2) using four 1/2 X 4-1/4” BOLTS(26),
Comments to this Manuals