Part # 6870101Revision:01/24/0018245102 LEG PRESS/CALFASSEMBLY INSTRUCTIONS
• SECURELY assemble one PAD (12) to the FRAME (2) using two 3/8 X 3” BOLTS (34) and two 3/8” WASHERS (36) as shown inFIGURE 7.100123 4 561/2 1/2 1
11FIGURE 8STEP 8:STEP 9:FIGURE 9• Snap two WEIGHT PLATE BUSHINGS (27) into thetop of all twenty WEIGHT PLATES (29) as shown inFIGURE 9. 27 2930 3
0123 4 561/2 1/2 1/2 1/2 1/2 1/212FIGURE 10STEP 12:• Insert two GUIDE RODS (13) into the base ofthe TOWER (1) as shown in FIGURE 10.Lubricate the G
13FIGURE 12• Place TOWER BRACE (8) over the GUIDE RODS (13) and SECURELY assemble TOWER BRACE (8) to TOWER (1) using two 1/2 X4” BOLTS (39), two
140123 4 561/2 1/2 1/2 1/2 1/2 1/2FIGURE 13• Route the swivel end of the CABLE (14) through the holes and around the pulleys in the TOWER BRACE (8)
FIGURE 1515STEP 15:• SECURELY assemble two 4-1/2” PULLEYS (21) to the brackets on the FRAME (2) using three 3/8 X 2” BOLTS (32), one CABLERETAINING
• Screw the threaded end of the CABLE (14) approximately 3/4” into the end of the 20 HOLE SELECTOR SHAFT (16) and tighten jamnut securely. See FIGU
• SECURELY assemble the SHROUD (11) to the TOWER (1) using four 3/8 X 1” BUTTON HEAD CAP SCREWS (30) as shown inFIGURE 18.FIGURE 1817STEP 18:Thank
IMPORTANT NOTESPlease note:Tools Required for Assembly* Thank you for purchasing the LIFE FITNESS 8245 LEG PRESS/CALF. Please read theseinstructions t
3PARTS LISTPART #6802903680480368038026780703680170368041026803503678130368020026803203679110268051016523401680740131161016284501671460132035016808901
STEP 1:FIGURE 1• LOOSELY assemble LOWER CROSS SUPPORT (4) to the TOWER (1) using two 1/2 X 4” BOLTS (39), two 1/2” WASHERS (40) and one1/2” LOCK
STEP 2:FIGURE 2• LOOSELY assemble the FRAME (2) to the LOWER CROSS SUPPORT (4) using two 1/2 X 4” BOLTS (39), two 1/2” WASHERS (40) andtwo 1/2” L
STEP 3:FIGURE 36• LOOSELY assemble the PIVOT FRAME (6) to the TOWER (1) using four 1/2 X 4” BOLTS (39), four 1/2” WASHERS (40) and three1/2” LOCK
7STEP 4:• Slide two 1-3/4” VINYL SLEEVES (22) over the shafts on the PIVOT ARM (7) as shown in FIGURE 4.• Slide one RUBBER BUMPER (21) over th
8FIGURE 5STEP 5:0123 4 561/2 1/2 1/2 1/2 1/2 1/2• SECURELY assemble the FOOTPLATE (3) to the PIVOT ARM (7) using four 1/2 X 4” BOLTS (39), four 1
STEP 6:9• SECURELY assemble the HANDLE (10) to the FRAME (2) using two 1/2 X 3” BOLTS (38), two 1/2” WASHERS (40), and two 1/2”LOCK NUTS (41) as s
Comments to this Manuals