M051-K50-A139 16 STACK MULTI-JUNGLE (SM63)WITH 3 ADJUSTABLE PULLEYSUNPACKING AND ASSEMBLY INSTRUCTIONS
SM63 Unpacking & Assembly Instructions10C. Prepare the weight stack. Slide the guide rods (2) through the weight stacks (1)as shown below. Place
SM63 Unpacking & Assembly Instructions116. Using a 7/8” combination wrench, bolt the floating pulleys into the 190 lb weightstacks (except for th
SM63 Unpacking & Assembly Instructions128. Mount the seated row and lat benches to the frame. Using the bolts specified inFigure 14 and a 9/16” s
SM63 Unpacking & Assembly Instructions13INSTALLING THE CABLESThe SM63 uses six cables. There are two different types of cable used on the SM63. Th
SM63 Unpacking & Assembly Instructions14ADJUSTABLE CROSSOVER CABLE ROUTINGOnce you’ve removed the pulleys as described previously, route the three
SM63 Unpacking & Assembly Instructions15Figure 18. Adjustable crossover cable end detail.Using a 7/8” wrench, tighten the jam nut onto the adjusta
SM63 Unpacking & Assembly Instructions16Bolt the cable to the weight stacks as shown in Figure 20. Thread the 7/8” nut up on the cablebolt as show
SM63 Unpacking & Assembly Instructions17 HARDWARE0123456½½½½½½Hardware Figure 1. Assembly Parts.
SM63 Unpacking & Assembly Instructions18The parts shown in Hardware Figure 1 are used to assemble the SM63. They are:A. 7/16” x 6” hex head bolt
SM63 Unpacking & Assembly Instructions19The part shown in Hardware Figure 3 is the 9/16” cable jam nut that’s used to secure thecables to the weig
SM63 Unpacking & Assembly Instructions2The SM63 comes partially assembled. Follow the steps below to complete the assembly.WARNING: COMPONENTS OF
SM63 Unpacking & Assembly Instructions20Hardware Figure 5. Top assemblies.S. Teardrop pulleys (bolt on above lat and seated row benches)T. 56” Lat
SM63 Unpacking & Assembly Instructions21Hardware Figure 6. Weight stack rubber bumpers.W. Weight stack rubber bumpers (inserted under weight stack
SM63 Unpacking & Assembly Instructions22PARTS LISTPart # ID Description QuantityMain components12345678CubesLat benchConnecting beamLat topsTricep
SM63 Unpacking & Assembly Instructions230017-00101-14130017-00104-03680017-00103-0217Pulley hardware(installed)1-3/4” BoltCap washer3/8” Nyloc nut
SM63 Unpacking & Assembly Instructions3 UNPACKINGFollow the steps below when unpacking the components of the SM63.1. Cut off the shipping wrapper
SM63 Unpacking & Assembly Instructions4 ASSEMBLYFigure 2 shows an assembled SM63.11752234468Figure 2. SM63 main components.1. Cubes (2)2. Lat ben
SM63 Unpacking & Assembly Instructions5Figure 3. Set the weight stack cubes.2. Bolt on the teardrop pulley assemblies above the benches (see Figu
SM63 Unpacking & Assembly Instructions6Figure 5. Configuration for 2-3/4” and 3” bolts.3. Using a 5/8” socket with long extension and combination
SM63 Unpacking & Assembly Instructions77/16” x 6” (2)-mount on topsRemove pulleys from housings to give clearance to socket extensionFigure 6. Bol
SM63 Unpacking & Assembly Instructions84. Using a 5/8” socket and combination wrench, mount the 56” lat tops (part T fromHARDWARE section) to the
SM63 Unpacking & Assembly Instructions9150 lb.weight stack300 lb.weight stack150 lb.weight stackFigure 9. Mount rubber bumpers and the weight stac
Comments to this Manuals